How to fix bottom of fence

That garden gate may be enough to discourage people from walking into your private yard -- but if the gap under the gate is too tall, it's probably not adequate for keeping your small dog from wriggling out.

Fortunately, you have lots of options for fixing that problem, whether the gate is made from wood, metal or something else. Secure chicken wire or wire mesh to the bottom of a chainlink, wood or wire gate. Cut a piece that is roughly double the length of the open area and as wide as your gate.

For example, if the gap is 3 inches tall with a width of 36 inches, cut a 6-inch by inch piece of chicken wire, using a pair of wire cutters. Hang the wire toward the bottom of the inside of the gate, letting the 3 inches hang down to the ground. Attach the wire to the gate with industrial staples or bits of wire wrapped around the existing gate and the wire.

Having a little extra wire attached to the body of the fence will give you more places to secure it to the gate. Putting the wire on the inside of the gate -- where your dog may reside -- may seem counter-intuitive, but it will make it more difficult for the dog to push through it completely. For a really determined dog, however, this might not be enough.

Secure a piece of firm rubber, like what you might use for weatherproofing your front door, to the bottom of the gate. Attach with bits of wire to a wire gate or industrial staples to a wooden gate.

Weld a D- or C-shaped iron bar to the bottom of an iron gate, effectively extending the total height of the gate. If you have a wooden gate, nail a two-by-four to the bottom of the gate as an extension that almost reaches the ground. Both of these options will require that you remove the gate first, so that you can work on the bottom of the gate with no obstructions.

Raise the ground underneath the gate with concrete, being careful not to pour the concrete so high that you can't open and close the gate.

To allow the concrete to form a bump below the gate, try cutting a wide piece of PVC piping in half to use as a form under which the concrete can set; but first ask your hardware store for a releasing agent to spray on the PVC. Alternatively, purchase a paver mold, and make the "bump" first and then set in place. The raised concrete will be similar to a speed bump, meaning it can be tripping hazard, so place reflective tape on it. For extra measure, you may want to place a cautionary sign on the gate, next to your "Beware of Dog" sign.

Lay rocks or river stones in the gap under the gate, if concrete is not feasible. This isn't going to be ideal for a large digging dog, but it might detract a smaller one.

how to fix bottom of fence

If you need to extend the fence because of a digging dog, also look for ways to improve your dog's behavior. Dogs often dig because of boredom or lack of exercise -- so taking your dog for a daily walk to decrease boredom and increase exercise can help.

Some dogs have separation anxiety and out of nervousness take off when their owners are away; ask your vet about possible treatments, if this is the case. Gently correct your dog when you see him digging there, but rely upon positive reinforcement to encourage good behavior -- for example, giving the dog a treat when he goes to the gate and does not try to escape. When adding an extension to the gate, ensure there are no loose ends of wire that could trap him, catch around his neck or cut him.

Whatever material you use to extend the bottom of the gate, ensure it is firm enough that your dog can't push under it. Nicole Vulcan has been a journalist sincecovering parenting and fitness for The Oregonian, careers for CareerAddict, and travel, gardening and fitness for Black Hills Woman and other publications. She's also a lifelong athlete and is pursuing certification as a personal trainer.

Skip to main content. Tip If you need to extend the fence because of a digging dog, also look for ways to improve your dog's behavior. Warning When adding an extension to the gate, ensure there are no loose ends of wire that could trap him, catch around his neck or cut him. About the Author Nicole Vulcan has been a journalist sincecovering parenting and fitness for The Oregonian, careers for CareerAddict, and travel, gardening and fitness for Black Hills Woman and other publications.

Customer Service Newsroom Contacts.When a wood fence starts to look shabby, it may seem easiest to just replace it entirely. But before spending the money and time—and throwing out perfectly usable lumber in the process—consider repairing that old fence instead. It isn't as hard as you might think! Here's how to complete three easy fixes for your wooden fence.

Fence posts naturally weaken and rot, whether they're cut from treated or untreated lumber, installed directly in contact with soil or encased in a concrete footing. It's more or less just a matter of time. Fence posts typically break at the greatest stress point, and once that happens, the adjacent fence sections start leaning over.

If you were to replace a rotted post, you'd need to take off the adjacent panels and get the old post—rotted end and all—out of the ground. Even if the post bottom is not set in concrete, it can mean a lot of digging and a lot of hassle to get the fibrous, crumbling end out of the hole.

If the post was set in concrete, it's even harder to get it out. You might as well dig a new post hole next to the old footing and offset the post spacing pattern. If you have only a few rotted posts, consider stabilizing them with steel splints or braces.

If the post in question isn't set in a concrete footing, E-Z Mender splints are the easiest, most effective hardware to apply. C are made for reinforcing 4 x 4 posts. They are U-shaped, inch long jackets made from gauge steel that's powder coated to prevent rust. One end of the jacket is shaped to a sharp point and the face has a nailing lug punched in it. To reinforce a weakened post, just insert the pointed end of the E-Z Mender against the post at grade, and drive it down with a sledgehammer until the top of the nailing lug is even with the ground.

You could fasten the splint to the post with hot-dipped galvanized nails, but I'd recommend using one-inch coated structural screws instead.

The manufacturer's recommendation is to install two E-Z Menders—one on each side of a weakened post. However, you may find you only need one to get the job done.Gaps under fencing are a nuisance; they can let unwanted wildlife into your yard or give your pets an escape route. The natural terrain of your yard can cause gaps to exist along the bottom of your fence, but gaps can be created with a poorly installed fence or when your dog thinks it must see what is going on outside your yard.

You can fill the gap between the ground and fence with different materials to stop the unwanted guests from visiting your yard and keep your beloved pet on its side of the property line. Fill the gap with all-purpose decorative stone or washed river rock.

how to fix bottom of fence

Choose stones sized between 1 and 3 inches in diameter. Multiply the length of the gap by the height and width of the gap to determine the cubic feet of the area. Purchase enough rocks or stones to fill the volume. Dump the rocks or stones into the gap beneath the fence. Use a bow rake to spread the rocks or stone over the area. Measure the gap height and length. Cedar fence pickets resist termites, deterioration and are less expensive than cedar dimensional lumber. The pickets will lie horizontally against your fence panel and parallel to the ground to fill the gap under the fence.

Position the cedar picket lengths horizontally, one above the other. For example, cut two pieces of cedar fence picket 3 feet long. Lay one piece of picket on the ground horizontally in front of you, and place the second picket piece above the first picket piece to create a piece of cedar fencing 3 feet long by 11 inches high. Cut 1- by 2-inch lumber into inch pieces. Place the 1- by 2-inch pieces of lumber vertically on top of the two horizontally positioned fence pickets every 8 to 10 inches.

These 10 inch pieces of lumber act as vertical braces along the horizontal lengths of cedar pickets. Enlarge the gap slightly with a shovel to fit the horizontal fence pickets down in the gap and against a wood-paneled fence. Drive 1-inch wood screws through the cedar pickets and into the wood fence.

How to Repair a Vinyl Fence

Thread ultraviolet-resistant cable ties through the holes and around the wires of a chain-link fence. Drill as many holes as necessary to secure the pickets to the fence. Tighten the cable ties to hold the pickets in place. Backfill any dirt you removed from the gap beneath the fence. Pack the dirt with the back of the shovel or your feet.During these challenging times, we guarantee we will work tirelessly to support you.

We will continue to give you accurate and timely information throughout the crisis, and we will deliver on our mission — to help everyone in the world learn how to do anything — no matter what.

Thank you to our community and to all of our readers who are working to aid others in this time of crisis, and to all of those who are making personal sacrifices for the good of their communities.

We will get through this together. Updated: January 29, References. Chain link fences often sustain minor damage from bad weather and falling debris, but this is something you can fix on your own. To fix a bad rail, start by purchasing and cutting a replacement rail.

You can use the pliers to install a mesh or fix smaller areas by weaving in new strands. Use a come-along tool to tighten the meshing and keep your fence strong. Repairing a chain link fence is fairly straight-forward, and most fixes can be done on your own. For more advice on measuring your new fence pieces, read on! Did this summary help you?

Yes No. Log in Facebook Loading Google Loading Civic Loading No account yet? Create an account. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy.Chain link fencing is a popular option for many homeowners seeking a means to keep their dog secure and safe.

Chain link is also used commercially by veterinarians, breeders and kennels to separate and secure dogs. There may be times when a gap is created along the bottom of a chain link fence, especially if a dog has been digging.

Securing the gap between the ground and the fence can be accomplished with a minimum of supplies. Move to a point where the fence is still near or in contact with the ground and just before the gap between the fence and ground begins.

Drive the stake into the ground with a hammer or mallet making sure that the hook catches the lower wire of the chain link. Drive the stake securely into the ground.

how to fix bottom of fence

Position the next stake 8 inches from the first and drive into the ground with the hook of the stake catching the fence.

Continue installing tent stakes across the gap. Fill the depression with gravel to help deter future damage to the area. Home Learn Behavior. Share on Facebook. Step 1 Locate the section of fence where there is a gap between the ground and the chain link fencing.

Step 2 Move to a point where the fence is still near or in contact with the ground and just before the gap between the fence and ground begins. Step 3 Place a tent stake with a hook next to the chain link fence with the hook toward the fence. Step 4 Drive the stake into the ground with a hammer or mallet making sure that the hook catches the lower wire of the chain link.

How to Repair a Wood Fence

Step 5 Position the next stake 8 inches from the first and drive into the ground with the hook of the stake catching the fence. Show Comments.Sign Up Sign In with Facebook. Asked on May 4, How to cover gaps at bottom of wood fence? I had this used privacy fence installed but because it was pre-made there are ugly gaps at the bottom. Looking for suggestions to cover this that will look nice but not cost a lot.

I'm also getting the grass going soon I hope!! Bar on May 4, Use a 1by 6 board to nail along the bottom of your fence. William on May 5, Would that cover the gap and be level?! Elizabeth Dion on May 4, Nail some 1x6's horizontally along the bottom, ideally, I would plant some evergreens along the fence line to hide the gaps. Or, install a raised flower bed with pavers around the whole bed. James on May 4, I had the same problem.

Fence post repair - how to fix broken, leaning fence posts - quick and easy with Post Buddy

Our neighbors have 2 small dogs that stuck their heads under and barked at us when we were in the back yard. I went to Lowes and bought some mini flagstone. I dug down and put gravel or you could use sand. Then laid the flagstone so they came close to the bottom of the fence.

This has worked quite well. We then planted different bushes along the fence. I hope you can enlarge this picture. Good Luck.

How to Close Gaps Under a Fence

NeNe on May 5, That's look awesome! Thank you for your help! Jerry on May 4, You could buy some bark at Home Depot and spread it about 12" wide at the bottom of the fence, deep enough to hide the gaps. And on May 5, Fill dirt and soil and grass seed maybe. Sandra Allen on May 5, Have you thought about good old fashioned cinder blocks? I know they aren't that pretty but if you paint them, you can set them with the holes up and put in either real or faux flowers. When you decide what to do please post it!!A vinyl fence is a very popular form of fencing for many urban homes.

The vinyl fence not only adds an attractive element to a landscape, but it is low in maintenance. These vinyl fences are mostly made of a non porous material that makes cleaning very easy. This also adds to the durability of the fencing, as it will not crack through water freezing inside the grain. There are some maintenance projects that do require a little more work than a normal cleaning.

Here are some steps to repairing a crack, or hole, in a vinyl fence. Before you do any repair work to the section of the vinyl fence where the crack is located, you should clean it of any dirt and debris. Use a clean cloth with a simple cleaning solution of water and dish detergent. Rinse it off completely and dry with another cloth. Wrap a piece of medium grit sandpaper around a small block of wood.

You do not want to use an electric sander for this operation, as you can gouge the vinyl or remove excess material. You are only trying to smooth out any burs and sharp edges around the hole. Rub the sandpaper in an area that is about 3 inches around the hole. Take a look at the hole in the vinyl fence.

If it is larger than 1 inch in diameter, you will need to use some expanding foam to fill in the hole. Spray the foam into the hole and fill as much of the vinyl fence as you can.

Fill the space slowly to allow the foam to expand. Do not stop until the foam begins to come out of the hole in the fence.

Let the foam dry overnight before doing any other work to the fence. Take a small handsaw, a coping saw works well for this, and remove the excess foam from the fence.

Cut as close to the fence as you can. After the foam has been cut down, use some medium grit sandpaper to smooth it out flush with the surface of the fence. Then, begin to concave the foam to form an inward dent.

After all of the sanding, you will need to clean the fence again. Wipe the surface with a damp cloth to remove any dust and debris from the foam and sanding. Using a small plastic scraper, fill in the area where the hole in the fence is. The purpose for the small indent in the foam is for the filler to be applied. Make sure you smooth it out so that it will be flush with the surface of the fence. Use the fine grit sandpaper and smooth the surface of the plastic filler.

Try not to remove too much material that will cause the filler to be lower than the fence.

Wipe the area clean and spray paint the color of the fence.